How to Drill a Water Well?

How to Drill a Water Well?

You all might be acquainted with what a water well is, but you may not know that subterranean aquifers contain over 97% of the world's freshwater, and to get access to that water, most homeowners prefer to set up a private water well. Besides this, they can be drilled for numerous reasons, including gauging water quality, for heating&cooling purposes, and providing drinking water when cleaned.

If you also plan to dig the well without seeking assistance from water well installation specialists in Carson City NV, then read the complete article to learn about the steps involved in the process.

However, numerous things must be addressed before digging a well, including necessary equipment, upfront cost, and recognizing any limitations prevailing in the region. While drilling a well can be strenuous and tedious, it's worthwhile in the long haul. Let’s dive in to learn about the drilling process without further ado.

A Guide to Drilling a Well

  • Determining the Drill Location:

Accessibility to the power supply and convenience are two pivotal aspects to weigh when determining the location of a well. Also, you must contact the relevant utility companies to ensure no subsurface pipes or lines are nearby. Any septic system or barn drainage must be positioned downward from the well.

  • Water Well Construction:

Water well digging is typically allocated for private property in locations lacking municipal or rural water sources. While you can hire trained water well drilling Fallon NV professionals for this service, they will cost you a hefty amount. Thus, DIY is the alternative most people prefer to save money. However, before commencing the task, you must get informed about the local regulations and ordinances. After this, collect info about your property by contacting your county's agricultural extension officer to get the details regarding the soil type you have, whether it's sandy, clay, rocky, or a combination of three.

  • Bore Holes in the Ground Using a Pneumatic Drill

It's a giant eggbeater operated by compressed air, available online, and can drill a 200-foot deep well in a couple of days or weeks, depending on soil type. However, you may need a strong air compressor and a drill for this equipment to work efficiently. Once you've garnered all the supplies and necessary equipment, execute the drilling process. But before drilling, an entire day of planning must be accomplished. Now, consider the steps below!

  • After determining the right location and having all the needed materials, commence digging the primary drill hole between 4 and 5 feet down using an auger or a post-hole digger. Subsequently, cut the 8-inch PVC to fit the hole, leaving a stick protruding out 4 inches above the ground.

  • Ascertain that the settling pond you dig is around 4 feet in diameter and 10 feet behind the well. After that, drill a thin, eight-inch deep canal to link the pond to the well hole.

  • Cover and link these gaps with 2-inch diameter PVC tubing, which is responsible for transferring clean water from the pond to the drill hole. Remember to cover the pond's pipe hole with netting to preclude trash from flowing back into the water well.

  • Now, put the 55-gallon drum along with the pond's edge, fasten it with pegs, and turn it to let the opening faces the well. Before the water is poured into the pond, it's pulled from the well to get collected in a drum. From the pond, it's then pumped back into the water well.

  • Utilize PVC glue to fasten a piece of 1-inch PVC pipe to the pneumatic drill and wrap it tightly with duct tape to prevent leaks. After that, set a market every five to ten feet to stay abreast of how far you've drilled. Insert the connected PVC pipe's opposite end in the 55-gallon barrel. While running the drill, water and mud will penetrate the pipe via small holes above the drill, driven upward by compressed air. After passing through the line into the drum and the settling pond, the mud and water will get recycled into the well bore.

  • Install the air compressor first and connect it to the training to operate the drill. Now, tie the air hose to the PVC pipe using duct tape to safeguard it from impeding the drilling operation process.

While the task might appear intimidating initially, with proper preparation and execution, it can be a hassle-free experience. You can enjoy drinking fresh, clean water from your well with a little elbow grease.

 

In case you have found a mistake in the text, please send a message to the author by selecting the mistake and pressing Ctrl-Enter.
Bruce MacKay Pump & Well Service, Inc. 0
Whether you want to install new water well, deepen an existing one, or clean water wells, you can trust Bruce MacKay Pump & Well Service, Inc. Here, you'll find...
Comments (0)

    No comments yet

You must be logged in to comment.

Sign In