Introduction
Automated sliding doors are an efficient and efficient solution for many public and commercial areas. They are designed to offer an effortless and smooth entrance and exit for the user while enhancing accessibility and efficiency in energy use. If you're thinking of installing an automated sliding door at your workplace this guide will provide step-by-step directions on how to go about it.
Step 1: Door Sizing
The first step when installing the automatic sliding doors is to establish the dimensions of the doors. Take measurements of the opening where it will be placed to ensure that you buy the right dimensions. The rough opening width will always be 1" greater than the door's frame's exact width. In the same way, the rough opening height will be 1/4" more than the frame's precise height. The rough opening must always be a little larger than the door's precise frame size to ensure an efficient operation.
Once you've decided on the door's size then you must purchase the appropriate hardware. This is typically the door track, operator or rollers, as well as any other accessories like switches or sensors. A majority of sliding doors that are automatic include this feature but it's important to ensure that all the components are available before starting installing.
Step 2: Electrical Requirements
The automatic sliding door requires 110VAC power to function. You'll need to run electrical wire to the place in which the door is to be placed. This could require help from an electrician, based on the degree of your knowledge.
The controller for the door operator typically has a labeled section that is for the main power connection. Follow the instructions of the manufacturer for connecting the operator to the wall to ensure that it's done correctly.
Step 3: Frame Installation
It is also the highest framework of a door's system. It is the home of the track where the door slides along and also all of the controls, electronics, gearbox, and motor. Start by attaching the frame jamb tubes to the header. After that, tilt the entire frame (header as well as jamb tubes) up. Set it carefully in the opening and attach the jamb tubes onto the wall using screws and bolts. Make sure that your frame is level and straight before fixing it on the wall's opening. Then, attach the track of your doors. The door track holds on the top of door panels to keep them from coming off of the track.
Step 4: Door Installation
Based on the type of door, you must follow the directions of the manufacturer to hang the doors according to the manufacturer's instructions for hanging the doors. For Com-AL sliding door systems that are automatic, the door panels are joined to the door by sliding the rail into the upper rail of the door and fixing it using screws. In other Com-AL models, they use the roller system and they must be positioned on top of the track, with the rollers holding the doors to the track. The rollers allow doors to move on the track. When connecting the rollers to the upper part of the door, make certain that the rollers and anti-rise rollers are correctly aligned to ensure that the doors move smoothly and equally. It may take some trial and error but it's crucial to ensure that the door is sliding smoothly and in a straight line with the track before proceeding to the next stage. Make sure that the top guideline of the door is moving with the track at the bottom. Adjust the guide at the bottom as needed.
Step 5: Sensor and Switch Installation
A lot of automatic sliding doors are with switches or sensors that let the door shut and open automatically. If your door is equipped with these parts, follow the directions of the manufacturer's installation. For Com-Al automated sliding doors, the sensors are wired in advance to work, so you just need to plug in the new sensors on the opposite side of the door's automatic header.
Typically it is the case that doormode switches have to be wired into. The switch is mounted to the inside of the jamb tube and connects directly to the automated Door Master Control Board.
Step 6: Final Adjustments and Testing
After all the parts have been installed, it's crucial to make an adjustment and test. Check that the door shuts and opens easily and is in alignment with the track.
Check the door's sensors or switches to verify that they're working correctly. Make adjustments as necessary to make sure that the door closes and opens at the right times and with the appropriate level of force. Always check ANSI requirements as well as any local regulations when tuning the automatic sliding door.
Conclusion
Installation of automatic sliding doors might appear to be a daunting job however, with the proper tools and directions it's an easy process. If you follow the steps laid out in this article to ensure that your sliding door is properly installed and runs effortlessly.
If you're not sure about a part of the installation process it is always recommended to seek advice from an expert. Here at Com-al Auto Door in Perth, we provide a broad selection of automated doors to make sure that you choose the ideal automated door for your specific needs.
No comments yet