Wavlink Aerial N300 Extender Setup

Wavlink Aerial N300 Extender Setup
4 min read

This article will cover three different Wavlink Aerial N300 extender setup, depending on your needs and intended application:

  • Router
  • Repeater 
  • Lan Bridge

The high-power amplifier technique eliminates dead zones in your environment. When set to its fastest setting, the Wavlink Aerial HS2 N300 can reach speeds of up to 600 megabits per second. This page contains setup instructions for the Wavlink N300 and Wavlink Aerial HS2 extenders.

Wavlink Aerial N300 Extender Setup in Repeater Mode

One of the simplest configuration steps is to set up your extender in repeater mode. Follow the instructions below to complete the Wavlink Aerial N300 extender setup in repeater mode:

  • The Aerial HS2 POE connector needs to be wired up with a power source first.
  • If the N300 has a strong green signal, connect the POE's Ethernet connection to the extender.
  • Remove any laptops, phones, or other wirelessly capable devices from the area.
  • Additionally, search for the WAVLINK-N network in the wireless settings menu.
  • After joining the default network, open a web browser that is compatible with Internet Explorer.There are three choices: Safari, Mozilla Firefox, and Google Chrome.
  • Now enter or ap.setup.
  • You have arrived at the Wavlink Aerial HS2 outdoor extender setup page.
  • To log in, enter the default password "admin."
  • The extender is now successfully configured to act as a repeater on your present WiFi network.

You cannot connect any cables from the POE to the main router or modem if you wish to operate your extender as a repeater.

How do I configure my Wavlink Aerial HS2 N300 WIFI extender?

The Wavlink Aerial N300 extender setup in router mode can be finished by following these steps:

  • It is first necessary to connect an outlet to the Wavlink N300 connection (POE) box.
  • The Ethernet wire from the POE box must be connected to the Aerial HS2 extension.
  • The second Ethernet cable should be connected to your main router or modem using the same connection box.
  • You can now join the WAVLINK-N network with any of your wirelessly capable devices.
  • After connecting, launch a browser and connect to wifi.wavlink.com.
  • Make "Router" your choice, then give your booster a catchy name.
  • From none, change the security to WPA2-PSK ( recommended ).Then click "Next" after entering your extender's password.
  • Now that the Wavlink outside extender has been set up in router mode, it is workable.

How can I update the Wavlink N300's firmware?

To fix any issues, you must update the firmware on your Wavlink N300. It offers additional features that will assist you in resolving your challenges in addition to extra security components.

Here are the tips to update the wavlink N300’s Firmware:

  • Your Wavlink Aerial HS2 is now active.
  • You can use any smartphone.
  • Go to Ap.setup.
  • After selecting settings, click firmware update.
  • To complete the firmware update procedure, refer to the instructions.
  • Don't unplug the repeater during the pause of one minute.

This explains how to update the Wavlink N300's firmware.

Wavlink Aerial N300 wifi extender factory reset

You must do a factory reset before you may reset your booster if you forget your admin username or password. When you reset the Wavlink N300, all of your personal data—including passwords, usernames, and SSIDs—is removed, getting ready your extender for a fresh setup process. For example, a paper clip or a needle will function to finish the factory reset procedure.

By performing the following, you can reset the Wavlink N300 Aerial:

  • A power supply must be connected to your Wavlink N300.
  • In the little hole underneath, look for the factory reset button.
  • Maybe on the side panel of the repeater.
  • Press the reset button for 8 to 10 seconds using a paperclip.
  • It will automatically restart after a while.
  • Now that you have your extender, you can start the new installation procedure.

You can get in touch with us via live chat or our toll-free phone if you still need help setting up your Wavlink Aerial N300 Extender. We are always available to assist you and provide a solution.

In case you have found a mistake in the text, please send a message to the author by selecting the mistake and pressing Ctrl-Enter.
Lisa Adler 2
Joined: 1 year ago
Comments (0)

    No comments yet

You must be logged in to comment.

Sign In / Sign Up